-
Maintenance Items Of Vacuum Pump For Blister Packing Machine
Nov 26 , 2021
Before the blister packaging machine working, the inlet pipe valves should be closed at first, so that the vacuum pump can run for over 15 minutes under the ultimate pressure state. This way can effectively extract the water pump in the gas. The motors should not be stopped and started frequently (the times is less than 6 time in one hour). (Notice: When the vacuum pumps are running normally, the ...
Read More
-
Development Prospect of Blister Packaging Machine
Nov 29 , 2021
In the last ten years, the development and research of China's high-speed aluminum-plastic blister packaging machine has been rapid, and some manufacturers, such as Guangdong Rich Packaging, have similar products that are basically equivalent in quality and performance to foreign products, but foreign products It is still in rapid development. The following are several development directions that ...
Read More
-
Functions And Features Of Blister Packaging Machine
Nov 29 , 2021
The complete machine of the blister packaging machine can be divided into separate packaging to enter the narrow elevator and the divided purification workshop. When the front and rear parts are combined, the screws are used for fastening, which is easy to assemble. When the machine is installed, the mold and the guide rail are designed independently, and only the integral guide rail is needed to ...
Read More
-
Structural Principle Of Blister Packaging Machine
Dec 08 , 2021
The current popular flat-plate blister packaging machine structure is composed of a base, a forming mechanism, a feeder, a heat-sealing and creasing mechanism, a punching mechanism, a traction manipulator, and electrical control. The main drive is driven by the cycloidal pin wheel deceleration and electric drive. The sprocket on the output shaft of the reducer drives the main shaft sprocket to run...
Read More
-
The Basic Operation Of Starting The Blister Machine
Dec 08 , 2021
The first is the first installation of the packaging material PVC rigid film and aluminum foil roll of blister packing machine: remove the compression nut and stop sleeve on the film reel, put the PVC rigid film or aluminum foil roll on the adjusting sleeve, install the stop sleeve and press tightly Screw the nut and tighten the nut so that the film cannot be loosened or rotated on the adjusting s...
Read More
-
Material Device Of Blister Packaging Machine
Dec 08 , 2021
Flat-plate aluminum-plastic blister packaging machine aluminum-plastic reel: sentence includes two parts: aluminum foil reel and plastic film reel. The reel is mainly composed of a cylinder, an inner and an outer stator, a brake ring, and an adjusting nut. The two ends of the cylinder are supported on a supporting shaft with rolling bearings, which are the rotating parts of the reel. When the plas...
Read More
-
Aluminum-Plastic Blister Packaging Machine Heat Sealing (Rolling Type And Plate Pressing Type)
Dec 22 , 2021
There are two ways to heat seal the aluminum-plastic blister packaging machine: roll pressing and plate pressing: 1. Rolling type The material to be sealed is passed between the two movable rollers to continue the sealing. However, the packaging material passes between the two movable rollers and stays under the pressure for a very short time. If you want to obtain a qualified heat seal, the rolle...
Read More
-
The Purpose Of Discussing The Contemporary Design Method Of The Aluminum-Plastic Blister Packaging Machine Cartoning Production Line
Dec 22 , 2021
The mechanical design of the aluminum-plastic blister packaging machine cartoning production line is based on the application requirements for the task principle, structure, activity method, force and energy notification method of the machine, the material and external dimensions of each part, and the smoothing method. Calculate and transform these into detailed descriptions as a basis for the tas...
Read More
-
The Composition Of The Blister Packaging Machine Depends On These Four Parts
Dec 22 , 2021
The blister packaging machine is a machine that forms a blister with a transparent plastic film or sheet, and seals the product between the blister and the bottom plate by means of heat sealing, bonding, etc. The composition of the blister packaging machine: The blister packaging equipment for medicines is basically similar to the blister packaging equipment for other products, and mainly consists...
Read More