-
Overseas Service Of Capsule Filling Machine
Jul 06 , 2021
In June, our Rich Packing company's engineers responsible for providing overseas services flew to Norway as planned to install and debug the capsule filling machine that arrived at the customer's place in advance. Our Rich Packing company provides customers with a free warranty service of up to 3 years. The service starts from the time the purchased machine arrives at the customer's designated loc...
Read More
-
Let's Talk About The Packaging Materials Of Aluminum Plastic Blister Machine
Jul 09 , 2021
PVC, PP, aluminum foil, dialysis paper, these are our common packaging materials used in aluminum-plastic blister machines. However, although these materials are the same packaging materials, there are many differences in performance and packaging requirements. For example, in terms of packaging time, dialysis paper or packaging materials with child-resistant structures usually take longer than or...
Read More
-
Njp-1500D Automatic Capsule Filling Machine Cleaning Operation Guide
Jul 10 , 2021
(1) Enter the manual page of the 1500D fully active capsule filling machine, and adjust the frequency to between 10Hz-15Hz. Raise the powder hopper, move the electric hand wheel of the main engine, raise the filling bracket to the highest point, unscrew the bolts at both ends of the filling bracket, add nuts as a spacer, adjust the two bolts to the same height, and place them under the filling bra...
Read More
-
Operation Guidelines For Fat Blister Packaging Machine
Jul 13 , 2021
We buy the aluminum-plastic blister packaging machine. After the assembly is completed in the workshop, the approximate operating steps of the aluminum-plastic machine we need to know are as follows: ① Clean the machine first. Prepare the pharmaceutical materials that need to be packaged, the outer packaging materials, and the production batch number template that needs to be replaced. Then instal...
Read More
-
What is a Multi-Punch Rotary Tablet Press
Jul 13 , 2021
At present, as people pay more and more attention to health, the drug and health care product market in the whole world has also become larger and larger. The demand for fast manufacturing of tablets is also increasing. At present, rotary tablet presses are widely used in most countries to make tablets. Rotary tablet press is also called multi-punch rotary tablet machine. The upper and lower punch...
Read More
-
Main Problems Of Blister Packing Machine
Jul 16 , 2021
NO. Question The Answer 1 What other device does the machine have to use? The blister packing machine needs to receive electricity, receiving water and air compressor before use; if receiving water, can use natural water or circulating water; if circulating water needs to buy water pump; can also bring water cooler. Generally, 260 machines must be equipped with cold coolers. 2 Size of package Both...
Read More
-
Installation And Maintenance Of Blister Packing Machine
Jul 16 , 2021
1.Unpacking the blister packing machine automatic and check for damage during transportation. 2. Machine shall be installed horizontally in the room without foot screws, with a 12mm thick rubber pad under the seat to avoid damage to the ground for long use and movement. To prevent vibration. 3. Fully clean it before startup, wipe the oil or dirt with soap water or detergent, and then dry it with a...
Read More
-
Cause Analysis And Solution Of Insufficient Hardness Of Tablets Compressed By Tablet Press
Jul 22 , 2021
During the normal operation of the tablet press, we will inevitably encounter the depressed tablets that are not hard enough. This is a very worrying job. Let's analyze the reasons and treatment methods that cause the pressure not to be hard. (1) Reason: The amount of adhesive or smoothing agent is small or inappropriate, so that the particles are unevenly distributed, and the coarse and fine part...
Read More
-
How To Deal With Tablet Weight Error Of Pharmaceutical Tablet Press
Jul 22 , 2021
1. The particle size distribution is not uniform, and the particle velocity is not the same when the tablet is pressed by the pharmaceutical tablet press, which leads to the uneven particle size in the mold hole. The particles should be mixed or the excessive fine powder should be screened out. 2. When the fine powder adheres to the punch to form a hanging punch, the difference of sheet weight is ...
Read More